VOR 530 SM 2002 - Czech rider

Hi,
My name si Daniel. I am from Czech republic. I am going to buy VOR 530 SM.
I am interested in parts on this moto. Are available now? Can be sent me to the Prague?
Thank you very much VOR riders!!!

Photo this beautiful Italian Supermotard:

VOR 530 SM 2002

E: I found this page: VOR parts Works this page?

Ciao Daniel!

if you can tell us wich part of the bike you need, maybe someone can help you, anyway we have the "mercatino" section, just try to take a look.

Ya bike looks nice, enjoy that!

BUT WHAT ABOUT THE CATERHAM?!!



the page you've found is correct, there you can find almost all you need for a Vor

great great great catheram..

CATERHAM?

Who produced parts on VOR? Vertemati?

All things besides things on the engine and the electrics can buy in Czech Republic.

Yes is'nt that a Caterham or a Lotus seven remake, near the Vor?

the parts... if there is anyone who still produce parts for our bikes, honestly I don't know, you better get in touch with Frigerio, they can explain everithing about the actual situation.

Message from Vertemati:

Dear Daniel,

for spare parts not problem, we sent catalog in the attached please make
list of spare parts after we sent estimate for this..

It is great!

This car isnt my. Its my neighbor. I dont know what is this.

Daniel_cz ha scritto:

Message from Vertemati:

Dear Daniel,

for spare parts not problem, we sent catalog in the attached please make
list of spare parts after we sent estimate for this..

It is great!

This car isnt my. Its my neighbor. I dont know what is this.

wow!! Good to know also for us in Italy!

Is many opportunities to get parts on VOR:

1. All things besides things on the engine and the electrics can buy in Czech Republic.
2. Slovak rider, Mrs. Katriňak gets almost everything on VOR.
3. Italian web site - FM FRIGERIO , where prices are?
4. Vertemati

It is absolutely amazing how many options I have to gets parts on VOR.

You're right Daniel,

for the prices you should call or even better email them at fmfrigerio@libero.it

Aniway, both Frigerio and Vertemati can sell new parts, and they are regular trading points, the other you mentioned I don't know so pay attention.

Pay attention Vertemati? Why?

E: I understand. Vertemati and FM are verified.

ciao daniel

non pensavo che cene fossero cosi' lontane....

So far in Czech republic?

How many people has approximately in Italy?

not so many, honestly....

but Czech republic is not so far where find a Vor, there are a few also from Australia and USA

It is true. In the Czech Republic has VOR more people. There are more in Slovakia than in Czech Republic.

E: Not so many in Italy?

Hi, I have problem.

We cleaned the carburetor (Keihin FCR 41), new plug and put a new fuel. VOR started great. Then I stopped the engine. After engine didnt start and began kicking me in the leg.
Where can be the problem? My tip is bad settings ignition.

THX Dan

Beautiful motard

Hi Daniel,

I suppose that you just have flooded your engine, so wetting up the spark plug it's impossible to start, almost until you're going to dry it..

A simple trick you can try is to close the petrol cock and place the bike on earth left to empty the carburetor bowl, and then try again.

We can not set the ignition. I need as much information about the ignition. (Rotor, Stator) THX

it's a tipical vor sm\E problem..with the ducati energia rotor\ignition.. the problem is the magnetic crown unglue.. the only precaution that you must pay close attenction during the fixing session is by a magnet crown position\phase.. even better if you can find a non metallic screw (alu or other , but important that are non magnetic..)..

VOR do not start, no way. Fresh gas, clean carburetor, spark throws, ignition settings by manual. Some tips?

you must follow the link posted by DRE , there are the way to fix the problem..you must open a flyweel ignition carter..all are perfectly explaned in the post linked befor by DRE..you will see that you will find the plastic crown of magnets that is detached from the flywheel and turn free , you must reattach that (or fix by non metallic screw : alu or other non magnetic stuff).. the phase of magnetic crown are explaned in the skatch in the tread linked befor..

sorry for the mackeronic english.. good luke dude..ahahah..

Davide

I need to know factory carburettor settings: (Not in the manual)

1. Position of the needle
2. Idling mixture

I have Keihin FCR 41.

THX.